2.7. Equipment of salon
Adjustment of seats
Front seats
|
Adjustment of provision of seats has to be made only on not movably standing car! |
In the Section Elements of security systems of the car important information on safety issues and correctness of adjustment of seats, their backs and head restraints is stated, - before a start of motion adjust as appropriate the provision of a seat.
For adjustment of provision of a seat in the longitudinal direction delay the bracket of a clamp located under a first line of a pillow up Holding a bracket in the lifted situation, shift assembly of a seat forward or back in situation, convenient for you, then release a clamp. For check of reliability of fixing of a seat try to shift it forward and back.
Adjustment of provision of a front seat in the longitudinal direction
|
Adjustment of a tilt angle of a seatback is made by means of the back of the rotary handle located from an internal side surface.
Adjustment of an inclination of a back of a front seat
|
The handle of adjustment of height of a pillow of a seat is located from an external forward corner of a pillow.
Adjustment of height of provision of a pillow of a front seat
|
The back clamp otpuskaniye lever allowing to make its folding is located in the top part of an external wall of a back. For folding of a back delay the lever up.
Folding of a back of a front seat
|
Head restraints
Head restraints help to prevent injuries of a neck and the head at blow of the car behind. In order that head restraints could perform effectively the protective functions, they have to be adjusted correctly. Adjust head restraints on height so that the top part of a pillow of a head restraint was flush with the upper edge of an auricle. If high passengers do not manage to achieve it, the head restraint needs to be established in the highest position. Adjustment of provision of a head restraint is made by two hands at the same time therefore it is not necessary to try to adjust a head restraint during the movement of the car. To lift a head restraint, incline it for the purpose of a clamp otpuskaniye forward, then pull it up / drown.
Adjustment of provision of a head restraint on height
|
Dismantle of a head restraint is made for cleaning or replacement as follows: lift a head restraint up to an emphasis, then press the buttons of clamps and release fixing cores from a seatback.
Dismantle of a head restraint
|
Back seat
Folding of a pillow and backs of a back seat
The back of a back seat has a separate design and consists of two parts which can develop forward, opening direct access to the luggage compartment and providing a possibility of transportation of large-size lengthy freights.
azhdy it can consist of two sections of a back of a back seat irrespective of another forward. Buttons of an otpuskaniye of clamps of backs are located from outer sides of their upper edges.
Adjustment of a corner of backs of a back seat
|
Expansion of the luggage compartment of the Corsa model can be made in three various ways.
Options of expansion of the luggage compartment
|
For expansion of the luggage compartment in the first way remove the back shelf and head restraints, incline backs of a back seat on a necessary corner and record them in the chosen situation.
For expansion of the luggage compartment in the second way remove the back shelf and head restraints and hang up locks of seat belts on backs of a back seat Press the unblocking button, lay a back of a back seat on a pillow of a seat and put the rental back shelf for front seats.
Fixing of locks of seat belts on a back of a back seat
|
For expansion of the luggage compartment in the third way remove the back shelf and head restraints, move front seats forward and hang up locks of seat belts on backs of a back seat. Raise a pillow of a back seat for a loop, and establish it in vertical position on a floor. Press the unblocking button, put a back of a back seat forward and put the rental back shelf for front seats.
Folding of a back of a back seat
|
At installation of a back of a back seat in a starting position release from under a back of a tape of seat belts.
Before return of a back to vertical position do not forget to release from under it a tape of a seat belt
|
For expansion of the luggage compartment affect the Combo models similar to the third way described for the Corsa model taking into account that the back shelf is absent, and for an unblocking of a seatback it is necessary to wring out lever clamps.
Folding of a back of a back seat on the Combo model
|
Head restraints
The back seat is equipped with three head restraints, left and right of which have the standard design similar to a design of head restraints of front seats.
When folding seats, or for the purpose of expansion of the sector of a rearview (at the unoccupied central place of a back seat) head restraints should be lowered in extreme lower situation, previously having released spring clamps of their cores.
Adjustment of provision of a head restraint of a back seat
|
Luggage compartment
Eyes for fastening of a safety net
On corners of the panel of half of the luggage compartment the metal eyes allowing to fix the safety network intended for fixing of the transported freight are provided.
The eyes located in corners of the panel of half of the luggage compartment are intended for fastening of a safety net or a protective lattice
|
|
By means of the same eyes on the Van models also protective lattice is fixed. |
Protective lattice (Combo models)
The protective lattice can be mounted behind backs of front seats (all Combo models), or behind a back of a back seat, (Combo Tour model).
Installation of a protecting lattice
|
For fastening of a lattice it is necessary to cut out a covering in the designated points and to fix a lattice from above and from below on both sides. After removal of a lattice close adjusting openings covers.
Lighter and socket of onboard power supply
Lighter
The lighter is located in forward section of the central console of the car and functions only at two provisions of a key in the ignition lock: "I \or "II", i.e. when ignition or food of auxiliary consumers of the electric power is included. For turning on of the lighter drown its button before click. After heat of a spiral the button automatically with click will return to a starting position.
Location of assembly of the lighter with an ashtray and sockets of onboard power supply
|
|
In order to avoid a lighter exit out of operation, do not hold its button during heating of a spiral! |
The nest under installation of the lighter at the same time carries out a role of the socket of onboard food which can include any auxiliary automobile accessories (the compressor, the vacuum cleaner, the charger for the mobile phone, etc.). For the purpose of ensuring access to the socket take the lighter from a nest. The consumers of the electric power connected thus at the switched-off ignition will work from the battery.
|
Power of consumption of the devices connected to onboard food should not exceed 240 W! |
Ashtrays
|
Use ashtrays only for the direct designated purpose! In order to avoid ignition do not put in ashtrays scraps of paper, a wrapper from candies and other combustible materials. |
The forward ashtray is united in uniform assembly with the lighter. For opening of an ashtray press the upper edge of its cover to clear an ashtray of stubs, open a cover of an ashtray and, having pulled up, take a reception container from the landing nest (address an illustration).
Ware boxes
The main ware box is located in the right part of the dashboard of the car and equipped with a folding cover. Opening of a box at the included ignition leads to automatic activation of its illumination.
The additional ware box is under a seat of the forward passenger and is extended for his handles forward. This ware box is calculated on loading no more than 1 kg.
Internal rear-view mirror
Internally the rear-view mirror is pasted by the basis on an internal surface of a windshield, from above in its central part. The rychazhok allowing to make switching of the reflecting surface in the night mode providing protection of eyes of the driver against dazzle with their light of the vehicles moving behind in the passing direction is provided in the lower part of assembly of a mirror.
Rychazhok of transfer of the reflecting surface of a rear-view mirror to the night mode is located in the lower part of assembly
|
Heating of front seats
At the tion corresponding a set switches of heating of front seats are located in a forward part of the central console under handles of management of a heater and marked with the pictogram
Arrangement of switches of heating of front seats
Control lamps of inclusion of heating of seats are built in switches. Switches of management of functioning of the electric drive of external rear-view mirrors On models with the manual drive of external mirrors adjustment of their situation is made by means of the bases of mirrors of rychazhok located from the inside. On the models equipped with the electric drive of adjustment of external rear-view mirrors, the switch of management of functioning of the electric drive is located from the inside of forward doors of the car in places of their adjunction to the dashboard.
Control unit of situation and heating of an external mirror
The choice of the mirror which is subject to adjustment is made by moving to the relevant party of the top polzunkovy switch. Actually adjustment is carried out by means of the lower rotational switch. Do not forget to return upon completion of adjustment the polzunkovy switch in average (neutral) situation in order to avoid risk of casual violation of required position of a mirror.
Switch of heating of external rear-view mirrors The switch of heating of external mirrors is in the control unit of situation and heating Inclusion of heating is followed by operation of the indicator close to the switch. Heating is turned off automatically in 15 minutes after its inclusion.