4. Engines
Specifications
General parameters
The full list of the engines and their parameters used for a complete set of the Opel Corsa-B/Combo and Tigra models
Volume, cm3
X10XE engine |
973 |
X12SZ engine |
1196 |
X12XE engine |
1199 |
C14NZ, X14SZ, C14SE, X14XE engines |
1389 |
X16XE, C16XE engines |
1598 |
Engines 4EC1, X15DT (T4EC1) |
1488 |
Engines 17D (4EE1), X17D (4EE1) |
1686 |
Engine type
X10XE engine |
1.0-12V DOHC |
X12SZ engine |
1.2 OHC |
X12XE engine |
1.2-16V DOHC |
C14NZ, X14SZ, X14SE engines |
1.4 OHC |
X14XE engine |
1.4-16V DOHC |
X16XE, C16XE engines |
DOHC |
Engine 4EC1 |
1.5 D OHC |
X15DT (T4EC1) engine |
1.5 TD OHC |
Engines 17D (4EE1), X17D (4EE1) |
1.7 D OHC |
Release period
X10XE engine |
05.1997 ÷ 08.2000 |
X12SZ engine |
03.1993 ÷ 03.1998 |
X12XE engine |
03.1998 ÷ 08.2000 |
C14NZ, C14SE engines |
03.1993 ÷ 02.1996 |
X14SZ engine |
03.1996 ÷ 08.1998 |
X14XE, X16XE engines |
09.1994 ÷ 08.2000 |
C16XE engine |
09.1993 ÷ 08.1994 |
Engine 4EC1 |
03.1993 ÷ 08.1996 |
X15DT (T4EC1) engine |
03.1993 ÷ 08.2000 |
Engine 17D (4EE1) |
09.1993 ÷ 02.1996 |
X17D (4EE1) engine |
03.1996 ÷ 08.2000 |
Engine capacity, kW/h.p. @ mines-1
X10XE engine |
40/55 @ 5600 |
X12SZ engine |
33/45 @ 4600 |
X12XE engine |
48/65 @ 5600 |
C14NZ engine |
44/60 @ 5200 |
X14SZ engine |
44/60 @ 5400 |
C14SE engine |
60/82 @ 5800 |
X14XE engine |
66/90 @ 6000 |
X16XE engine |
78/106 @ 6000 |
C16XE engine |
80/109 @ 6000 |
Engine 4EC1 |
37/50 @ 4800 |
X15DT (T4EC1) engine |
49/67 @ 4600 |
Engine 17D (4EE1) |
44/60 @ 4500 |
X17D (4EE1) engine |
44/60 @ 4400 |
Torque, Nanometer @ mines-1
X10XE engine |
82 @ 2800 |
X12SZ engine |
88 @ 2800 |
X12XE engine |
110 @ 4000 |
C14NZ engine |
103 @ 2800 |
X14SZ engine |
106 @ 3000 |
C14SE engine |
114 @ 3600 |
X14XE engine |
125 @ 4000 |
X16XE engine |
148 @ 4000 |
C16XE engine |
150 @ 3800 |
Engine 4EC1 |
90 @ 2400 |
X15DT (T4EC1) engine |
132 @ 2600 |
Engine 17D (4EE1) |
108 @ 2600 |
X17D (4EE1) engine |
112 @ 2650 |
Diameter cylinder/piston stroke, mm
X10XE engine |
72.5/78.6 |
X12SZ engine |
72.0/73.4 |
X12XE engine |
72.5/72.6 |
C14NZ, X14SZ, C14SE, X14XE engines |
77.6/73.4 |
X16XE, C16XE engines |
79.0/81.5 |
Engines 4EC1, X15DT (T4EC1) |
76.0/82.0 |
Engines 17D (4EE1), X17D (4EE1) |
79.0/86.0 |
Extent of compression
X10XE, X12XE engines |
10.1 |
X12SZ engine |
10.0 |
C14NZ engine |
9.4 |
X14SZ engine |
9.6 |
C14SE engine |
9.8 |
X14XE, X16XE, C16XE engines |
10.5 |
Engines 4EC1, 17D (4EE1), X17D (4EE1) |
23.0 |
X15DT (T4EC1) engine |
22 |
The arrangement/number of cylinders//the Number of valves on the cylinder
SOHC engines |
line / 4//2 |
DOHC engines, except X10XE |
line / 4//4 |
X10XE engine |
line / 3//4 |
Operating procedure of cylinders
Engines, except X10XE 1-3-4-2 (the first cylinder is located from the GRM drive).
X10XE 1-2-3 engines |
1-2-3 |
Normal direction of rotation of a bent shaft
Clockwise.
Compression pressure
Petrol engines |
|
Nominal rate, atm |
12 ÷ 15 |
The maximum admissible difference between cylinders, atm |
1 |
Diesel engines |
|
Nominal rate, atm |
not less than 22 |
The maximum admissible difference between cylinders, atm |
1.5 |
Maximum admissible frequency of rotation, rpm
See Specifications to the Head Nastroyki and routine maintenance of the car.
Working parameters of engines
Head of cylinders
The maximum admissible not planeness of the interfaced surface, mm |
|
Petrol engines |
0.013 |
Diesel engines |
0.025 |
Height of a head of cylinders, not less, than a mm.
Petrol engines |
|
L DOHC 1.0 and 1.2 engines |
126 |
L OHC 1.2 and 1.4 engines |
95.25 ±0.45 |
L DOHC 1.4 and 1.6 engines |
134.70 |
Diesel engines |
131.25 |
Tilt angle of facets of saddles of valves, hail. |
45 |
Valves and the directing plugs
The size of a gap of landing of a core of the valve in the directing plug, mm
Petrol engines |
|
SOHC engines |
|
Inlet valves |
0.018 ÷ 0.052 |
Final valves |
0.038 ÷ 0.072 |
DOHC engines |
|
Inlet valves |
0.030 ÷ 0.060 |
Final valves |
0.040 ÷ 0.070 |
Diesel engines |
|
Inlet valves |
0.020 ÷ 0.200 |
Final valves |
0.030 ÷ 0.250 |
Height of the installed valves, no more, than a mm
Petrol SOHC engines |
14.4 |
Tilt angle of working facets of plates of valves
SOHC engines |
44 |
DOHC engines |
45 |
Failure of valves concerning the interfaced surface of a head of cylinders of the diesel engine, mm |
0.5 ÷ 1.0 |
Vystupaniye of the vortex camera of the diesel engine over the interfaced surface of a head of cylinders of the diesel engine, mm |
0.0 ÷ 0.03 |
Conrod and piston assemblies
Piston vystupaniye size, no more, than a mm |
|
L OHC 1.2 and 1.4 engines |
0.22 |
L DOHC 1.0, 1.2, 1.4 and 1.6 engines |
0 |
Lubrication system
Pressure of motive oil, atm |
|
Normal value |
|
Petrol engines |
1.5 |
Diesel engines |
2.0 |
Minimum value |
|
Petrol engines |
0.3 |
Diesel engines |
2.0 |
Type of the oil pump
Petrol engines | Gear, with the direct drive from a bent shaft |
Diesel engines | Rotor, with the direct drive from a bent shaft |
Pressure range regulated by the reducing valve, bar |
|
Engines 1.0 and 1.2 DOHC |
4.4 ÷ 6.4 |
Efforts of tightening of threaded connections, Nanometer
Bolts of fastening of wheels |
110 |
D/V of pressure of motive oil |
30 |
Petrol engines
SOHC engines
Bolts of fastening of covers of the GRM drive |
|
External covers |
4 |
Bolts of fastening of a cover of the gas-distributing mechanism |
8 |
Camshaft cogwheel bolt |
45 |
Bolts of a back persistent plate of the camshaft |
8 |
Bolts of a face cover of the GRM case |
12 |
Bolts of fastening of the module of ignition |
8 |
Fixture of a reception pipe to a final collector |
25 |
Fixture of the inlet pipeline to a head of cylinders |
20 |
Fixture of a final collector to a head of cylinders |
20 |
Thermostat fixture |
10 |
Bolts of fastening of the water pump |
8 |
Bolt of a pulley of a bent shaft *
M12 bolt | |
|
95 |
|
to hold on on a corner on the 30th hail. |
|
to hold on the 15th hail on a corner. |
M10x23 bolt |
22 |
M10x23 bolt |
22 |
|
55 |
|
to hold on on a corner on 45 ÷ 60th hail. |
Bolts of fastening of a head of cylinders *
|
25 |
|
to hold on the 60th hail on a corner. |
|
to hold on the 60th hail on a corner. |
|
to hold on the 60th hail on a corner. |
Bolts of fastening of a cover of a flywheel |
7 |
Cap of the reducing valve of the oil pump |
30 |
Bolts of fastening of a maslozabornik |
8 |
Bolts of fastening of the pallet of a case of the engine |
|
Models without To/in (the stamped steel pallet) |
|
Bolts of fastening of the pallet to the block of cylinders / to the oil pump |
8 |
Drain stopper of the pallet |
55 |
Models with To/in (the cast aluminum pallet) |
|
Bolts of fastening of the pallet to the block of cylinders / to the oil pump |
8 |
Bolts of fastening of a flange of the pallet to a transmission case |
40 |
Drain stopper |
45 |
* Use new bolts.
L DOHC 1.0 and 1.2 engines
Bolts of fastening of the case of the GRM drive | 8 |
Bolts of fastening of the water pump | 8 |
Fixture of the top pro-rate of a chain of the GRM drive | 8 |
Bolts of fastening of a cover of the GRM case | 8 |
Bolts of fastening of the module of ignition | 8 |
Bolt of fastening of an asterisk of the camshaft |
|
|
50 |
|
to hold on the 60th hail on a corner. |
Stopper of a natyazhitel of a chain of the GRM drive |
20 |
Stopper of a natyazhitel of a chain of the GRM drive |
60 |
Opening stopper for a stopper of a bent shaft |
60 |
The case of an oil filter to a head of cylinders |
20 |
Fixture of the top thermofilter of a final collector |
8 |
Fixture of lock levels of the engine |
20 |
Fixture of the K/V compressor |
20 |
Fixture of the holder of the catalytic converter |
15 |
Fixture of the catalytic converter |
35 |
Bolts of fastening of the inlet pipeline to a head of cylinders |
20 |
Bolts of fastening of a final collector to a head of cylinders |
20 |
Fixture of the directing tube of the probe of level of motive oil |
8 |
Thermostat case cover |
8 |
Shtekerny level of injectors |
8 |
Pulley of the water pump |
20 |
The lower holder of a plait of an electrical wiring to a final collector |
10 |
Top and lower bolts of a support of a final collector |
25 |
The back holder of a plait of an electrical wiring to a final collector |
6 |
The PCV valve to the holder of a final collector |
6 Nanometer. |
Bolts of fastening of a head of cylinders * |
|
|
25 |
|
to hold on the 60th hail on a corner. |
|
to hold on the 60th hail on a corner. |
|
to hold on the 60th hail on a corner. |
Oil pump |
|
Fixing bolts |
8 |
Screws of fastening of a cover of the pump |
8 |
Cap of the reducing valve |
30 |
Bolts of fastening of a maslozabornik * |
8 |
Bolts of fastening of the stamped steel pallet of a case of the engine * |
|
Bolts of fastening of the pallet to the block of cylinders / to the oil pump |
10 |
Bolts of fastening of a flange of the pallet to a transmission case |
40 |
Drain stopper of the pallet |
10 |
The damping plate to the block of cylinders |
8 |
* Use new bolts.
L DOHC 1.4 and 1.6 engines
Bolts of covers of the GRM drive |
|
Back cover |
5 |
Bolt of fastening of a natyazhitel of a belt of the GRM drive |
20 |
Fixture of a reception pipe of system of release to a final collector |
25 |
Fixture of a reception pipe of system of release to the catalytic converter |
18 |
Fixture of a cover of VV of wires |
4 |
GRM case cover bolts |
8 |
Bolts of fastening of the top part of the inlet pipeline |
8 |
Bolts of fastening of the inlet pipeline to a head of cylinders |
20 |
Bolts of fastening of a final collector to a head of cylinders |
22 |
Bolts of fastening of a branch pipe of a butterfly valve to the top part of the inlet pipeline |
8 |
Bolts of fastening of the CKP sensor |
8 |
Bolt of fastening of a cogwheel of a bent shaft * |
|
|
95 |
|
to hold on the 30th hail on a corner. |
|
to hold on the 15th hail on a corner. |
Bolt of fastening of a cogwheel of the camshaft * |
65 |
Bolts of fastening of a head of cylinders * |
|
|
25 |
|
to hold on the 90th hail on a corner. |
|
to hold on the 90th hail on a corner. |
|
to hold on the 90th hail on a corner. |
|
to hold on the 45th hail on a corner. |
Forward right support of the engine to the holder of the power unit |
60 |
The holder of the power unit to RKPP and a support of the engine |
60 |
The holder of the power unit right to a head of cylinders |
65 |
The holder of the power unit right to the block of cylinders (model with GUR) |
60 |
The holder of the power unit back to RKPP |
70 |
The block of depreciation of the engine to a forward longitudinal beam of a frame |
65 |
The block of depreciation of the engine behind to the bottom |
65 |
Bolts of fastening of the block of depreciation of the engine on models with GUR |
29 |
Oil pump |
|
Fixing bolts |
8 |
Screws of fastening of a cover of the pump |
8 |
Cap of the reducing valve |
30 |
Bolts of fastening of a maslozabornik * |
8 |
Bolts of fastening of the pallet of a case of the engine * |
|
L models 1.4 and 1.6 without To/in (the stamped steel pallet) |
|
Bolts of fastening of the pallet to the block of cylinders / to the oil pump |
8 |
Drain stopper of the pallet |
55 |
L models 1.4 and 1.6 with To/in (the cast aluminum pallet) |
|
Bolts of fastening of the pallet to the block of cylinders / to the oil pump |
8 |
Bolts of fastening of a flange of the pallet to a transmission case |
60 |
Drain stopper |
45 |
* Use new bolts.
Diesel engines
The holder of support of the engine to the engine block |
45 |
The damping engine support to a longitudinal beam of a forward frame and to the holder of a suspension bracket |
60 |
Bolts of fastening of covers of bearings of the camshaft |
15 |
Bolts of fastening of a cover of a head of cylinders |
8 |
Bolts of fastening of the lower cover of a gear belt |
10 |
Bolts of its fastening of a pulley of a bent shaft |
20 |
Fixture of a tension roller |
20 |
Fixture of a cover of a head of cylinders |
8 |
Fuel highways to TNVD and nozzles |
25 |
The top bolts of fastening of a back cover of a gear belt to a head of cylinders |
10 |
Bolts of fastening of a cogwheel of the camshaft |
10 |
Bolts of fastening of the thermofilter of a final collector |
10 |
Bolts of fastening of the inlet pipeline to a head of cylinders |
30 |
Bolts of fastening of a final collector to a head of cylinders |
30 |
Bolts of fastening of a head of cylinders |
|
|
40 |
|
to hold on 60 ÷75 hail on a corner. |
|
to hold on 60 ÷ 75th hail on a corner. |
Bolts of fastening of a maslozabornik * |
8 |
Bolts of fastening of the steel pallet of a case of the engine |
|
Bolts of fastening of the pallet to the block of cylinders |
10 |
Drain stopper of the pallet |
75 |
* Use new bolts / nuts.