13:17. Removal and installation of facing of doors

Cars from 09.1998 g of release can be completed with the side safety cushion which is built in on each side seatbacks of the driver and forward passenger. Seats with a side safety cushion are marked with white stripes with the red inscription "AIRBAG". The sensor of a safety cushion is from each party behind facing of a door. On the cars equipped with side safety cushions follow safety rules during the work with elements of side safety cushions and emergency natyazhitel of belts.

Removal of facing of a forward door (all models)

 PERFORMANCE ORDER

  1. Carefully disconnect an overlay of the internal handle of opening of a door. Disconnect the handle (arrows). Separate the VCh socket of the loudspeaker (1).

Bolts of fastening of the handle (arrow) and VCh socket of the loudspeaker (1)

  1. Squeeze out the switch of the electric regulator of an external mirror from within the driver's door, separate its socket and remove the switch.

Removal of the switch of the electric regulator of an external mirror

  1. Turn out bolts of fastening of a pocket of a door and wring out the wide screw-driver two clamps At the corresponding complete set separate the socket of an electrical wiring of the switch of the power window and remove a door pocket.

Door pocket fixture
A — Combo
B — the Sedan

  1. On the Combo model wring out clamps of a triangular overlay of an external mirror from a door frame in its top part.

Clamps of an overlay of an external mirror

  1. At the corresponding complete set remove the handle of movement of glass of a forward door. For this purpose wring out the OPEL-KM-317-A tool a wire clip. It is possible to apply pincers of HAZET-799 also. If there are no tools stated above, wring out a clip the narrow screw-driver in the direction of an arrow.

Removal of the handle of movement of glass of a forward door

  1. Remove the handle from its axis. If at removal the spring was squeezed completely out, again press a spring into a handle groove. Remove a plastic washer.
  2. Remove an internal sealant of glass of a forward door by means of the plastic pallet.

Removal of an internal sealant of glass

  1. On the Corsa and Combo models turn out bolts (shooters).

Bolts of fastening of facing (Corsa and Combo model)

  1. On the Tigra model turn out three bolts from the lower edge of a door. Disconnect by means of the plastic pallet facing from a door behind and in front, having opened at the same time clamps.

Bolts and clamps of facing (Tigra model)

  1. Remove facing via the button of blocking of a door up.
  2. If it is necessary, carefully remove a sealing film from a door frame. Previously wring out clamps (shooters).

Clamps of a sealing film

Removal of facing of a back door (Corsa model)

 PERFORMANCE ORDER

  1. Disconnect an overlay of the internal handle of opening of a door (3), turn out screws of fastening and remove the handle of a back door (1).

The components preventing removal of facing of a back door

  1. Remove the handle of movement of glass of a back door (2).
  2. Remove a triangular slip in a back part of a door.

Removal of a triangular slip

  1. Turn out bolts of fastening (arrow) and remove facing up.

Facing fastening bolts

  1. Remove internal consolidation of glass of a back door up.

Installation

 PERFORMANCE ORDER

  1. Accurately paste a sealing film to a door frame. Stick gaps with an adhesive tape.

On cars with a side safety cushion replace the damaged film. It is of great importance for the correct operation of a side safety cushion.

  1. Connect sockets of an electrical wiring of switches of the regulator of an external mirror and window regulator (at the corresponding complete set).
  2. Put on an upholstery via the inclusion button, expose it on a frame of a door and fix.
  3. Fix a door pocket by screws.
  4. Fix the door handle. Connect the loudspeaker VCh socket.
  5. At the manual drive of glass of a door put on a handle axis a plastic washer the high party in the direction of facing.
  6. Put on the handle of movement of glass of a door an axis and slam it a hand. At the same time the spring lock has to enter a groove on an axis. The handle has to be turned down at the closed window.
  7. Press an internal sealant of glass.
  8. Fix a triangular slip and handles of a door.